Lifeboat Foundation

Researchers at the Indian Institute of Technology Bhubaneswar, in collaboration with TCS Research and Wageningen University, recently devised a new strategy that could improve coordination among different robots tackling complex missions as a team. This strategy, introduced in a paper pre-published on arXiv, is based on a split-architecture that addresses communication and computations separately, while periodically coordinating the two to achieve optimal results.

The researchers’ paper was recently presented at the IEEE RoboCom 2022 conference, held in conjunction with IEEE CCNC 2022, a top tier conference in the field of networking and distributed computing. At IEEE RoboCom 2022, it received the Best Paper Award.

“Swarm-robotics is on the path to becoming a key tool for human civilization,” Dr. Sudipta Saha, the lead researcher of the team that carried out the study, told TechXplore. “For instance, in medical science, it will be necessary to use numerous nano-bots to boost immune-therapy, targeted and effective drug transfer, etc.; while in the army it will be necessary for exploring unknown terrains that are hard for humans to enter, enabling agile supervision of borders and similar activities. In construction, it can enable technologies such as large-scale 3D printing and in agriculture it can help to monitor crop health and intervene to improve yields.”

In a groundbreaking new study, researchers at the University of Minnesota Twin Cities used a customized printer to fully 3D print a flexible organic light-emitting diode (OLED) display. The discovery could result in low-cost OLED displays in the future that could be widely produced using 3D printers by anyone at home, instead of by technicians in expensive microfabrication facilities.

The research is published in Science Advances.

Continue reading “Researchers develop first fully 3D-printed, flexible OLED display” »

You might not have to send your devices in (or buy replacement parts) if the display breaks — you could just make new screens yourself. University of Minnesota Twin Cities researchers have developed what they say is the first fully 3D-printed flexible OLED display. In theory, you wouldn’t have to depend on panels made at large, distant factories to build or repair your gadgets.

The new approach combines two methods of 3D printing to print the six layers needed for a functional display. The team used extrusion printing to make the electrodes, encapsulation, insulation and interconnects, while active layers were spray-painted at room temperature. Past attempts by various teams either had issues with light uniformity (consistency across the whole panel) or relied on techniques beyond 3D printing to put some components in place, such as spin-coating or thermal evaporation.

The prototype was just 1.5 inches wide and used just 64 pixels. Any practical uses would require much higher resolutions (a 1080p display requires over 2 million pixels), and the scientists also want to improve brightness. It might also take a while to adapt the technology for home use. The university used a custom 3D printer that costs as much as a Tesla Model S — it might take a while for the method to be viable on off-the-shelf printers, even including high-end models like FormLabs’ $4,850 3B+.

Formlabs, one of the few companies to turn 3D printing into a useful, real-world tool, is here at CES to show off two new printers. The Form 3+ and 3B+ are updates to the models it launched in 2019, with these units described as its “fastest 3D printers to date.”

New for 2022 include higher-intensity lasers, new material settings and faster, more durable hardware, with a promise of 40 percent faster prints. It also comes with the Build Platform 2, an updated deck for manufacturing that makes it easier to remove prints when they’re done.

At the same time, the company is showing off ESD Resin, enabling you to build components that dissipate electrostatic discharges. This should, Formlabs hopes, open up new opportunities for prints that can be used inside the electronics industry and other high-tech operations.

Virginia mom April Stringfield is now the owner of Habitat for Humanity’s first 3D-printed home — built in record time, thanks to new construction tech.

The massive time and money savings from 3D printing means the nonprofit is very likely to print more in the future.

Continue reading “3D-printed home cuts construction time from 4 weeks to 28 hours, says Habitat for Humanity” »

A major obstacle to widespread study and clinical use of 3D tissues is their short shelf-life, which may be anywhere from a just few hours to a few days. As in the case of an organ transplant, a bioprinted tissue must be transported rapidly to the location where it is needed, or it will not be viable. In the journal Matter on December 21^st, researchers at Brigham and Women’s Hospital and Harvard Medical School describe their work combining 3D bioprinting with cryopreservative techniques to create tissues which can be preserved in a freezer at-196°C and thawed within minutes for immediate use.

“For conventional bioprinting, there is basically no shelf life. It’s really just print, and then use, in most cases,” says lead author Y. Shrike Zhang (@shrikezhang), a biomedical engineer at Brigham and Women’s Hospital. “With cryobioprinting, you can print and store in the frozen state for basically as long as you want.”

Continue reading “3D-bioprinted tissues can now be stored in the freezer until needed” »

Updating the goal of Chang’e 8 mission.

Chinese space authorities told state media South China Morning Post (SCMP) that the unmanned lunar station, jointly built with Russia, will be completed around 2027.

The new plan, which is eight years earlier than previously scheduled, will help China get ahead of the U.S. in the space race.

Continue reading “China’s Unmanned Lunar Station Will Be Ready in 2027 Amid Space Race With the US” »

One Virginia family received the keys to their new 3D-printed home in time for Christmas.

The home is Habitat for Humanity’s first 3D-printed home in the nation, according to a Habitat news release.

Janet V. Green, CEO of Habitat for Humanity Peninsula and Greater Williamsburg, told CNN it partnered with Alquist, a 3D printing company, earlier this year to begin the process.

Today, magnets have many applications being used for energy generation, data storage, and computing. But magnetic computing devices in two-dimensional systems are quickly approaching their shrinking limit.

That’s why, we have witnessed a growing trend in moving to three dimensions, where higher densities can be achieved and three-dimensional geometries can offer new functionalities.

Now, an international team led by Cambridge University’s Cavendish Laboratory has used an advanced 3D printing method they developed to create magnetic double helices that produce nanoscale topological textures in the magnetic field, opening the door to the next generation magnetic devices.